Plating is the cheapest line on a K gold quote and the most expensive to get wrong. A 0.3 micron difference decides whether a piece survives a season or comes back as a tarnish complaint.
What the micron number means
Plating thickness is measured in microns, one thousandth of a millimetre. On K gold, 0.3 micron is a fashion finish, 0.5 is a season, 0.8 to 1.0 is daily wear, and 1.5 and above is the jewelry standard for a plated piece sold as long-wear.
Ask for the number per finish, not per factory. Rhodium, gold tone and e-coat have different targets.
Put the forecast window in writing. Capacity priority follows predictability, not friendship.
The four failure modes
First, tarnish at the contact points: the shank inner face, the clasp and the ear post. Second, plate skip at the prong tips. Third, colour drift between lots. Fourth, blistering after the e-coat.
Each has a cause: insufficient thickness, poor pre-plate cleaning, bath chemistry drift, or cure temperature. A K gold claim sheet should name the cause, not just the defect.
| Finish | Thickness | Expected life | Use |
|---|---|---|---|
| Rhodium, thin | 0.3 micron | One season | Fashion |
| Rhodium, standard | 0.8 micron | Daily, 12+ months | Core line |
| Gold tone | 0.5-1.0 micron | Season to daily | Core line |
| E-coat over plate | +2-3 micron | Tarnish barrier | Humid markets |
Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.
Write the remedy matrix before the first defect: remake, credit, allowance or rework, each tied to a defect class.
Specifying plating in the PO
Write four lines: base metal preparation, plating type, thickness in microns, and the wear test. Add the salt-spray or wear-hour standard you will accept.
Then test the first lot: rub the contact points with a cloth for 30 seconds and check for colour transfer. A simple test catches most thin-plate lots.
Repair and replating policy
Plated goods need a replating path. Ask whether the factory will replate a returned piece and at what cost. A supplier with no replating service leaves you to absorb the return.
For K gold at volume, a replating agreement is worth more than a 3 percent price concession.
Keep the approved sample and the CAD together. One proves what was agreed, the other proves what was made.
What to check before the order
Run the five checks below in order. The first two protect the money, the last three protect the launch date.
- Ask for microns per finish, not a trade name.
- Test contact points on the first lot.
- Write the wear standard into the PO.
- Agree a replating path and price.
- Check colour drift against the approved sample.
If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.
Frequently Asked Questions
How thick should K gold plating be?
0.8 micron rhodium for daily wear, 0.5 for a seasonal line, 1.0 or more for long-wear claims.
Why does plating wear at the shank first?
It is the contact point with skin and other rings. Thickness and pre-plate cleaning decide how long it lasts.
Can plating be reapplied?
Yes, if the base metal is clean. Ask for the replating cost and turnaround before you need it.
Does e-coat change the colour?
It can add a slight warmth. Ask for a coated sample before approving the colour.
Is thicker plating always better?
Up to a point. Too thick a plate can look heavy and can crack at the prong tips if the deposit is stressed.
How do I know a supplier is reliable?
Two clean repeat lots and two on-time shipments. Before that it is a sample, not a supplier.
Send the K gold finish requirement. We return the micron spec per finish, the wear test standard and the replating terms. See the full range at K Gold and HOLYCOME.
Buyers who get consistent lots are not luckier. They wrote the spec down and checked the first carton against it.