Jewelry Tools

Jewelry Tools: Returns and Claims: A Process That Settles in Seven Days - HOLYCOME

Jewelry Tools: Returns and Claims: A Process That Settles in Seven Days - HOLYCOME

A jewelry tools defect is not a relationship problem. It is a document problem. Photograph, compare to the approved sample, and agree a remedy in writing, and most claims settle inside a week.

Step one: the photo pack

Shoot the defect on white, with the PO number in frame, plus one wide shot and one macro shot. On jewelry tools, a loose stone needs a side view at the prong seat; a plating issue needs a raking light shot.

Send the pack within seven days of arrival. Late claims are weaker claims, and factories know it.

Put the gram weight per size on the PO, not an average. Cost and feel both follow weight, and an average hides the size that breaks the margin.

Step two: compare to the approved sample

The approved sample is the contract. Put it in a sealed bag with the PO number at approval, and keep it for the life of the program. A claim without a reference sample becomes a negotiation.

Where the sample and the lot differ on a jewelry tools dimension, the measurement decides, not the opinion.

DefectEvidenceRemedyWindow
Loose stoneMacro side viewRemake or credit7 days
Plating wearRaking light shotReplate10 days
Wrong sizeCaliper readingExchange7 days
PorosityMacro surface shotRemake7 days
Missing pieceCarton and packing listCredit3 days

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Sample by size run, not from one mixed tray. Defects cluster by size and by design, and a mixed sample hides both.

Step three: choose the remedy

Four remedies: remake, credit, price allowance, or rework at the factory's cost. Critical defects get remake or full credit. Minor cosmetic marks get an allowance.

Never take an allowance on a critical defect. A sharp edge or a missing stone is a safety and compliance issue, not a discount opportunity.

Step four: close the loop

Ask for the root cause with the remedy: which step failed, and what changed. A factory that cannot name the step will repeat it.

Log every jewelry tools claim by defect type and month. Three claims of the same type is a process signal, not bad luck.

Keep the approved sample and the CAD together. One proves what was agreed, the other proves what was made.

What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Send the photo pack within seven days.
  • Keep the approved sample sealed.
  • Measure, do not opine.
  • Refuse allowances on critical defects.
  • Log claims by defect type and month.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

Frequently Asked Questions

How long do I have to claim a jewelry tools defect?

Seven days for visible defects, ten for plating wear that shows after a wear test. Put the window in the PO.

What photos does a claim need?

A wide shot, a macro shot and a raking light shot, each with the PO number visible.

Is a credit or a remake better?

Remake for critical and for designs still selling. Credit for end-of-season or discontinued SKUs.

Can I claim after resale?

Only if the defect was latent and documented. Most programs limit claims to the incoming inspection window.

What if the factory disputes the claim?

Send the measurement and the approved sample photo. Numbers settle disputes that adjectives prolong.

Should I buy stock or made to order?

Stock for the top three designs, made to order for the tail. Stock cover is a calculation from sell-through and lead time.

Send the jewelry tools defect photos and the PO number. We return a root-cause note and a remedy within two business days. See the full range at Jewelry Tools and HOLYCOME.

The short version: specify the number, seal the sample, inspect against both. Everything else is negotiation.

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .